Image shown is a representation only.

Exact specifications should be obtained from the product data sheet.

Original Mini ZVS Tapeless Finished Mini Edition Induction Heating Jacob Ladder Driver

Manufacturer Product Number
M160
Description

Mini ZVS Tapeless Finished Mini Edition Induction Heating Driver module

Package Condition
Bulk

Product Brief introduction

1. This non tapping mini board ZVS finished board, high-voltage package, cooling fan, etc.

2. This kit requires a certain level of hands-on ability and relevant knowledge. If you don't even know how to use a soldering iron or how to separate the positive and negative poles of the power supply, it is recommended not to take photos. If there is a problem with the purchase, the seller will not be held responsible!

3. Power ≤ 120W (when using 12V induction heating). Pushing high voltage pack 12V, with primary 5+5 turns, around 30W.

4. The input voltage is DC 5V~12V, which is the voltage during operation, not the voltage when the power supply is unloaded!

5. Confirm that all components are welded correctly, the positive and negative poles of the power cord are not reversed, connect the load (heating coil, high-voltage package), and then turn on the power! No load, no power supply! It is easy to damage when powered on without load!

6. Heating coil: The width of the object being heated should be between 1/3 and 1/2 of the inner diameter of the heating coil, and should not exceed 2/3 at most! The diameter of the heated object should be controlled within 20mm as much as possible. If it is too large, it will be difficult to heat it until it turns red, as the power is limited.

When induction heating is used, power off and cooling is usually required after 5 minutes of operation. Because the current is relatively high during induction heating, the coil also heats up significantly. During heating, some of the heat generated by the heated object is transferred to the heating coil, and over time, the temperature of the heating coil will become very high. If the heating coil is connected to the terminal block, the plastic part of the terminal block will melt off! Therefore, it is best to directly solder the heating coil to the PCB board during induction heating. Please pay attention to this point for buyers. For long-term use, it is recommended to use copper pipes as coils and cool them with water.

7. The current during high-voltage charging and induction heating is related to the input voltage, number of primary turns, number of heating coil turns, and size of the heated object. Our store's testing is for reference only!

8. Blue LED power indicator light, check whether the light is on or off to determine if there is power!

Product Function

Possible reasons for the indicator light not turning on include:

1. The wire is not connected properly and the power supply is not powered on.

2. The board has damaged components.

When the indicator light is dim, it should be due to insufficient power supply and a higher power supply needs to be replaced.

Tapeless ones are more suitable for induction heating.

详情-04

详情-05

How to use:

1. Weld the heating coil directly onto the PCB board

2. Input voltage: DC5-12V

3. Place the heated object: The width of the heated object should be between 1/3 and 1/2 of the inner diameter of the heating coil, and should not exceed 2/3 at most!

The diameter of the heated object should be controlled within 20mm as much as possible. If it is too large, it will be difficult to heat it until it turns red, as the power is limited.

详情-06

Product Show

主图-02

主图-01

Payment&Transportation

详情8.1

Official Certificate&Certificate

详情页3.1

Multiple product supply

详情5.1

Company office environment

详情6.1

Warehouse Real Shot

170019007688325e.png

Standard packaging

详情9

We also provide :

Part No Manufacturer Date Code Quantity Description
LM22676ADJ NS 19+ 250 SOP8
TPS562201DDCR TI 22+ 795500 SOT23-6
NJG1806K75 JRC 22+ 500000 DFN6
TLV74318PDQNR TI 22+ 402000 X2SON-4
NJG1801K75 JRC 22+ 300000 SMD
NJG1804K64 JRC 22+ 300000 DFN8
LM27761DSGR TI 22+ 151000 WSON8
TLV62565DBVR TI 22+ 138000 SOT23-5
TPS613222ADBVR TI 22+ 108000 SOT23-5
LNK625DG-TL POWER 22+ 100000 SOP-8
OPA4322AIPWR TI 22+ 100000 TSSOP14
TLV75528PDRVR TI 22+ 99000 WSON-6
TPS7A2025PDQNR TI 22+ 78500 X2SON-4
TLV62568DBVR TI 22+ 72000 SOT23-5
STM32L051K8U6TR ST 22+ 60000 QFN32
SKY66421-11 SKYWORKS 22+ 56500 QFN16
TPS7A1111PDRVR TI 22+ 54000 WSON6
TLV62569PDDCR TI 22+ 52000 SOT23-6
TLV62569DBVR TI 22+ 48000 SOT23-5
TPS23753APWR TI 22+ 40000 TSSOP14
NB691GG-Z MPS 22+ 30000 QFN
SN74AHC1G02DBVR TI 22+ 27939 SOT-23
TPS63000DRCR TI 22+ 23238 VSON10
TLV75533PDRVR TI 22+ 21500 WSON6
NB687BGQ-Z MPS

Write your review

Original Mini ZVS Tapeless Finished Mini Edition Induction Heating Jacob Ladder Driver

Mini ZVS Tapeless Finished Mini Edition Induction Heating Driver module

Write your review

Other Products In The same category:

5000In stock:
Can ship immediately
QUANTITY
All prices are in USD

SEND
RFQ