Temperature controller STC-1000 aquarium hatching seafood machine electronic digital display microcomputer controller switch

Module Parameter

Product Name: Digital Microcomputer Temperature Controller

Product Name: STC-1000

Measurement range:- 50℃~99℃

Measurement accuracy: ± 1 ℃ (-50 ℃~70 ℃)

Resolution: 0.1 ℃

Whole machine power consumption: less than 3W

Sensor: NTC sensor (1 meter)

Environmental temperature: 0~60 ℃

Relative humidity: 20-85% (no condensation)

Overall dimensions: 75 * 34.5 * 85MM

Installation opening: 71 * 29mm

Shell material: ABS flame retardant plastic shell

Output Capacity: Refrigeration (10A/250VAC) Heating (10A/250VAC)

Product Features

Indicator light status description：

Menu Description：

Key operation instructions

1. Method for viewing parameters:

When the controller is working normally, press and immediately release the ▲ key once to display the temperature setting value; Press and immediately release the ▼ key once to display the temperature difference setting value. Return to normal temperature display status after 2 seconds.

2. Parameter setting method:

When the controller is working normally, hold down the "S" key for more than 3 seconds to enter the parameter modification mode. The "Set" indicator light will be on, and the digital display will show the code of a menu item. Press the "▲" or "▼ Save parameter modifications and return to normal display state. If there are no key operations within 10 seconds, the parameter modifications will not be saved and return to normal display state

If there is an error when saving parameters, it will display "Er" for 3 seconds and return to the normal display state.

Power supply: 110-220VAC ± 10%, 50/60Hz (or DC12V/DC24V)

Measurement and control temperature range:- 50℃~+110℃

Resolution: 0.1

Accuracy: ± 1 ℃

Relay output contact capacity: Heating: 10A/240VAC,

Refrigeration: 10A/240VCA

Sensor H-type: Imported NTC sensor, with a wire length of 1 meter

Shell material: gray ABS flame-retardant plastic shell

Net weight 120g Gross weight 140g Press and hold Set for 5 seconds to enter internal parameter settings

Press up and down to switch P0... P8, press Rst to confirm and return

P0 cooling and heating mode

Please set the cooling mode to C when starting at high temperature

Low temperature start for heating mode, please set it to H

P1 hysteresis setting

In heating mode (H): When the measured value is less than or equal to the set value and there is a difference, the output will start heating until the set value is reached and stop

In cooling mode (C): When the measured value is ≥ the set value+hysteresis, start outputting cooling until the set value stops

P2 maximum setting range: The maximum value when setting the temperature does not exceed this value

P3 minimum setting range: When setting the temperature, the minimum value should not be lower than this value

P4 temperature calibration: When there is a difference between the measured temperature and the standard temperature, this function can be used for calibration. The calibrated temperature is equal to the temperature before calibration plus the calibration value

P5 delayed start time unit: minutes. When controlling the compressor equipment for cooling, the delay time can be set as needed. When the controller outputs, the equipment will not start immediately and needs to run the set delay time before starting

P6 high temperature alarm: When the measured value is greater than this value, the screen displays a beep alarm and forcibly disconnects the output

P7 Data Lock Function: Enabling the data lock can keep the current settings unchanged. At this time, setting the temperature and function are invalid. If modification is needed, the data lock function needs to be turned off

P8 factory reset

Long press SET to switch to P8, press SET once to set on, press Rst to restore factory settings

Product Size

Product Show

Payment&Transportation

Official Certificate&Certificate

Multiple product supply

Company office environment

Warehouse Real Shot

Standard packaging

We also provide ：